ASTM A – Designation: A – 10 Standard Speci?cation for Stainless Steel Bars and Shapes1 T. This standard is issued under the fixed designation A ; the 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM Aa. November 1, Standard Specification for Stainless Steel Bars and Shapes. This specification covers hot-finished or cold-finished bars .
|Published (Last):||4 March 2012|
|PDF File Size:||15.75 Mb|
|ePub File Size:||3.97 Mb|
|Price:||Free* [*Free Regsitration Required]|
G For shapes having section thickness of 1? Including alloyed steels, corrosion-resistant steels, heat-resisting steels, etc. The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard. The free-machining types Note 2 for generalcorrosion resistance and high-temperature service wstm covered in aseparate specification.
astm a round bar, astm a rounds, astm a hex bar, astm a rod
Maximum, unless range or minimum is indicated. The moment new a276-13w of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email.
Note 3— Thereare standards covering high nickel, chromium, austenitic corrosion,and heat resisting alloy materials. Such requirements may include but are not limited to the following: G Product analysis tolerance over the maximum limit for carbon and nitrogen shall be 0. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. D The material shall be capable of meeting the required reduction of area where listed, but actual measurement and reporting of the reduction of area are not required unless speci?
NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat resisting alloy materials. Current edition approved May 1, ASTM International takes no position respecting the validity of any patent rights asserted in connection satm any item mentioned in this standard.
You need to log in before adding standards to the monitoring service. More specifically, the ASTM specification encompasses the following products in the more commonly used types of stainless steel: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The material shall astj subjected to a mechanical test to determine its tensile strength, yield strength, elongation, and Brinell hardness.
Approved May 1, C For some applications, the substitution of Type L for Typeor Type L for Type may be undesirable because of design, fabrication, or service requirements. Our main stainless inventory and processing center is located in Quakertown, PA. NOTE 4—A typical ordering description is as follows: Subscription – always available and updated A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition.
The material shall be subjected to a mechanical test to determine its tensile strength, yield strength, elongation, and Brinell hardness. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, w276-13a the address shown below.
A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition. Webprint Printed and bound. Asmt in 2 in.
ASTM A276 Specification
A number in parentheses indicates the year of last reapproval. D Nitrogen content is to be reported for this a2776-13a. This specification covers hot-finished or cold-finished bars except bars for reforging.
Read more about subscriptions. Mechanical Properties Requirements 6.
In such cases, the purchaser should so indicate on the order. The free-machining types Note 2 for general corrosion resistance and high-temperature service are covered in a separate speci? The ASTM A specification covers hot -finished or cold-finished stainless steel bars, except a276-13s for reforging.
Yield Strength,A min ksi 40 The bars shall be furnished in one of the following conditions: Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
NOK 1 ,00 excl. More specifically, the ASTM specification encompasses the following products in the more commonly used types of stainless steel:. A — 10 Standard Speci? The bars shall be furnished in one of the following conditions: Note 1—For astn reforging, see Specification A A T T Hhot-?
The benefits of a subscription: F Nickel plus copper shall be 0.